Enter into the IoT Era with a Real Time Controller PAC（Programmable Automation Controller）Series

I/O Modules

I/O interface expansion modules of the configurable type controllers.
24 VDC power is supplied by the controller to the attached I/O modules via the internal bus.

Analog Input and Output Modules

M2M controllerseries   PACseries   Edgeseries

Model	Input	Output	Power Consumption	Connectors	Controller series
CPS-AI-1608LI	8-ch differential input, 16-bit resolution, ±10V Bus isolated	―	100mA（Max.）	Screw terminal block (3.81mm/0.15" pitch)
CPS-AI-1608ALI	8-ch differential input, 16-bit resolution, 0-20mA Bus isolated	―	100mA（Max.）
CPS-AO-1604VLI	―	4-ch voltage output, 16-bit resolution, ±10V Bus isolated	200mA（Max.）
CPS-AO-1604LI	―	4-ch current output, 16-bit resolution, 0-20mA Bus isolated	200mA（Max.）

Sensor Module

Model	Supported sensor / wiring method	No. of CH / Isolation	Power Consumption	Connectors	Controller series
CPS-SSI-4P	Pt100／ Three-wire or four-wire	4ch／Bus isolated	50mA(Max.)	Screw terminal block (3.81mm/0.15" pitch)

Digital Input and Output Modules

Model	Input	Output	Power Consumption	Connectors	Controller series
CPS-DIO-0808L	8-ch Opto-isolated (Compatible with current sink output)	8-ch Opto-isolated open-collector (Current sink type)	50mA(Max.)	Screw terminal block (3.81mm/0.15" pitch)
CPS-DIO-0808BL (Built-in 12VDC power)			120mA（Max.）
CPS-DIO-0808RL	8-ch Opto-isolated (Compatible with current source output)	8-ch Opto-isolated (Current source type)	100mA(Max.)
CPS-DI-16L	16-ch Opto-isolated (Compatible with current sink output)	―	100mA（Max.）
CPS-DI-16RL	16-ch Opto-isolated (Compatible with current source output)	―	100mA（Max.）
CPS-DO-16L	―	16-ch Opto-isolated open-collector (Current sink type)	100mA（Max.）
CPS-DO-16RL	―	16-ch Opto-isolated (Current source type)	100mA（Max.）

Relay Module

Model	Input	Output	Power Consumption	Connectors	Controller series
CPS-RRY-4PCC	―	4-ch Relay contact output (1 pair of Form c contacts)	N/A	Screw terminal block (50.8mm/0.2" pitch)

Counter Module

Model	Input	Output	Power Consumption	Connectors	Controller series
CPS-CNT-3202I	Phase A/Up 1×2ch Phase B/Down 1×2ch Phase Z/CIR 1×2ch General input 1×2ch Optocoupler isolated between channels	Match signal output 1×2ch (Opto-isolated open-collector output)	N/A	Screw terminal block (3.81mm/0.15" pitch)

Serial Communication Modules

Model	Transmission Scheme	No. of CH / Isolation	Power Consumption	Connectors	Controller series
CPS-COM-1PC	RS-232C Asynchronous serial transmission	1ch／ Bus isolated	90mA(Max.)	9-pin D-SUB connector (s)
CPS-COM-2PC		2ch / Bus isolated Isolated between channels	110mA（Max.）
CPS-COM-1PD	RS-422A/RS-485 Asynchronous serial transmission (Full duplex / half duplex)	1ch / Bus isolated	110mA（Max.）	Screw terminal block (3.81mm/0.15" pitch)
CPS-COM-2PD		2ch / Bus isolated Isolated between channels	150mA（Max.）

LoRa Communication Modules

Model	Wireless System	Frequency band / Modulation method	No. of Channels	Power Consumption	Connectors	Controller series
CPS-COM-1QL (Japan only)	ARIB STD-T108	920.6～928.0MHz LoRa (Spread Spectrum)	15ch (at 62.5 and 125kHz bandwidth) 7ch (at 250kHz bandwidth) 5ch (at 500kHz bandwidth)	100mA（Max.）	SMA connector

• *
  24 VDC power is supplied by the controller to the attached I/O modules via the internal bus.

Insulation Deterioration Monitoring Module for Three Phase Induction Motor + ZCT Sensor

Model	The Measured Circuit	No. of measured circuit	Inner diameter of ZCT	Measurement voltage range	Measurement leakage current range (Resolution: 0.001 mA)	Measured insulation resistance range	Controller series
CPS-MM-LC	Overall equipment measurement (power supply mode) / Inverter output section measurement (inverter mode)	1ch	Φ25mm (Φ0.98”)	Line voltage 10 VAC or more, 600 VAC or less	Overall equipment measurement: 0 to less than 1A Inverter output section measurement: 0 to less than 100 mA	Less than 1,000MΩ*

• *
  The guaranteed accuracy range is less than 10 MΩ

• IoT Solution：Three-Phase Motor Breakdown Prediction Monitoring

Options

Power Supplies

• *
  A DC cable and a 3-pin I/O connector are included.
• *
  AC power cable is not included. An optional AC power cable is available from Contec (IPC-ACC0DE3).

3G Antenna

AC Power Cable

IO-Link Master

Roof Top Antenna

Connection Cable for FANUC CNC

Connection Cable for Mitsubishi Electric CNC

Magnet (for mounting)